国产免费啪视频观看网站-国产免费区-国产免费全部免费观看-国产免费人成在线视频视频-国产免费爽爽视频免费可以看

1、 C6C64C64T C6C64C64T 連接維護說明書
Correctly connect the output side (terminal U, V, W). The servomotor will not run properly if incorrectly connected. Always install an AC reactor per each power supply unit. Alw

2、 C6C64C64T C6C64C64T 參數說明書(eng).pdf
Set up a compensation factor for reducing a control error in the reduction of a corner roundness and arch radius. Indicates a maximum control error (mm) in parentheses. The larger the

3、 C6C64C64T C6C64C64T 參數說明書
(1) Word and address A word is a collection of characters arranged in a specific sequence. This entity is used as the unit for processing data and for causing the machine to execute specifi

4、 C6C64C64T C6C64C64T 編程說明書 (M系)
For items described in "Restrictions" or "Usable State", the instruction manual issued by the machine manufacturer takes precedence over this manual. An effort has been made to note as man

5、 C6C64C64T C6C64C64T 編程說明書 (M系)
(1) Address check This function enables simple checking of progr am addresses in word units. If the alphabetic characters are continuous, the program error (P32) will occur. Availability of t

6、 C6C64C64T C6C64C64T 編程說明書 (M系)
在ISO 碼中，從控制出“（”起至控制入“）”（或“；”）止的所有信息均被視為無效。 定顯示裝置。因此，可在此間輸入與指令紙帶的名稱編號等控制沒有直接關系的信息。 但是，紙帶存儲時此間的信息（“紙帶碼一覽表”的（B）除外）也被存儲。 電源接通時為控制入狀態(tài)。

7、 C6C64C64T C6C64C64T 編程說明書 (L系)
校驗檢查是檢查紙帶是否正確作成的一種方法。它是檢查打在紙帶的編碼有無錯誤的方法，可用校驗V 及校驗H 兩種方法檢查。 （1） 校驗H 校驗H 是檢查是構成一個字符的孔數是否正確，適用于紙帶運轉、紙帶輸入、順序編號呼叫等情況。 以下情況會產生校驗H 錯誤。 （a ） ISO碼 在有意義數據區(qū)間中，碼的孔是奇數個。 （例1） 校驗H 錯誤的例子（ISO 碼時

8、 C6C64C64T -C6C64C64T PLC接口說明書(eng)
Introduction This manual describes the various signal interfaces and functions required when creating MELDAS C6/C64/C64T sequence programs (built-in PLC). Read this manual thoroughly bef

9、 C6C64C64T C6C64C64T DDB接口說明書
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un

10、 C6C64C64T C6C64C64T DDB接口說明書
(Note 1) The unit systems B and C are settings for t he setup parameters (basic specification parameters: #1003 iunit). This may differ according to the machine type. (Note 2) The un

11、 C6C64C64T C6C64C64T DDB接口說明書
This is a parameter for the maximum spindle speed of each gear step. (This corresponds to the setup paramet er, spindle parameter smax1 to 4.) The CNC creates the spindle gear shift command 1

12、 C6C64 C6C64 規(guī)格說明書
Ff1 : Feed rate (1) The arc plane is designated by G17, G18 or G19. (2) G02 or G03 is used to designate the direction of the arc rotation. (3) Absolute or incremental values can be as